Company News

PVH81 Series Open-Circuit Axial Piston Pump

PVH81 Series Piston Pump — Model Table ith Pressure / Speed Data

Source basis: Eaton Vickers PVH81 frame size (81 cm³/rev nominal), open-circuit variable displacement. Parameters below follow the PVH standard coding logic (control code, shaft code, seal/pressure class, mounting code), so the same model number always maps to the same pressure–speed envelope.

Parameter legend

Code Meaning
QIC Load-sensing (LS) + pressure compensator, 350 bar class
AIC Pressure compensator only (constant pressure), 350 bar class
BIC Constant-power / torque-limiting, 320 bar class
RSF / LSF Right / left rotation, side ports (SAE flange)
10S / 02S Spline shaft (SAE C) / keyed shaft
10 / 11 / 20 / 21 Compensator spring setting (standby & LS differential, low → high)
C25 / C21 NBR seal pack, 350 bar / FKM (Viton) seal pack, 350 bar, high-temp
31 / 32 / 41 SAE 4-bolt flange, side ports / SAE 4-bolt flange, rear ports / ISO 4-bolt mount

Hot-selling model

Model Number Disp. (cm³/rev) Rated Press. (bar) Peak Press. (bar) Max Speed (rpm)
PVH81QIC-RSF-10S-10-C25-31 81 350 420 2200
PVH81QIC-RSF-10S-11-C25-31 81 350 420 2200
PVH81QIC-RSF-10S-20-C25-31 81 350 420 2200
PVH81QIC-RSF-10S-21-C25-31 81 350 420 2200
PVH81QIC-RSF-10S-10-C25-32 81 350 420 2200
PVH81QIC-RSF-10S-11-C25-32 81 350 420 2200
PVH81QIC-RSF-10S-20-C25-32 81 350 420 2200
PVH81QIC-RSF-10S-21-C25-32 81 350 420 2200
PVH81QIC-RSF-10S-10-C25-41 81 350 420 2200
PVH81QIC-RSF-10S-11-C25-41 81 350 420 2200
PVH81QIC-RSF-10S-20-C25-41 81 350 420 2200
PVH81QIC-RSF-10S-21-C25-41 81 350 420 2200
PVH81QIC-RSF-02S-10-C25-31 81 350 420 2000
PVH81QIC-RSF-02S-11-C25-31 81 350 420 2000
PVH81QIC-RSF-02S-20-C25-31 81 350 420 2000
PVH81QIC-RSF-02S-21-C25-31 81 350 420 2000
PVH81QIC-RSF-02S-10-C25-32 81 350 420 2000
PVH81QIC-RSF-02S-11-C25-32 81 350 420 2000
PVH81QIC-RSF-02S-20-C25-32 81 350 420 2000
PVH81QIC-RSF-02S-21-C25-32 81 350 420 2000
PVH81QIC-LSF-10S-10-C25-31 81 350 420 2200
PVH81QIC-LSF-10S-11-C25-31 81 350 420 2200
PVH81QIC-LSF-10S-20-C25-31 81 350 420 2200
PVH81QIC-LSF-10S-21-C25-31 81 350 420 2200
PVH81QIC-LSF-10S-10-C25-32 81 350 420 2200
PVH81QIC-LSF-10S-11-C25-32 81 350 420 2200
PVH81QIC-LSF-10S-20-C25-32 81 350 420 2200
PVH81QIC-LSF-10S-21-C25-32 81 350 420 2200
PVH81QIC-LSF-02S-10-C25-31 81 350 420 2000
PVH81QIC-LSF-02S-11-C25-31 81 350 420 2000
PVH81QIC-LSF-02S-20-C25-31 81 350 420 2000
PVH81QIC-LSF-02S-21-C25-31 81 350 420 2000
PVH81QIC-RSF-10S-10-C21-31 81 350 420 2200
PVH81QIC-RSF-10S-11-C21-31 81 350 420 2200
PVH81QIC-RSF-10S-20-C21-31 81 350 420 2200
PVH81QIC-RSF-10S-21-C21-31 81 350 420 2200
PVH81QIC-RSF-10S-10-C21-32 81 350 420 2200
PVH81QIC-RSF-10S-11-C21-32 81 350 420 2200
PVH81QIC-RSF-10S-20-C21-32 81 350 420 2200
PVH81QIC-RSF-10S-21-C21-32 81 350 420 2200
PVH81AIC-RSF-10S-10-C25-31 81 350 400 2200
PVH81AIC-RSF-10S-11-C25-31 81 350 400 2200
PVH81AIC-RSF-10S-20-C25-31 81 350 400 2200
PVH81AIC-RSF-10S-21-C25-31 81 350 400 2200
PVH81AIC-RSF-10S-10-C25-32 81 350 400 2200
PVH81AIC-RSF-10S-11-C25-32 81 350 400 2200
PVH81AIC-RSF-10S-20-C25-32 81 350 400 2200
PVH81AIC-RSF-10S-21-C25-32 81 350 400 2200
PVH81BIC-RSF-10S-10-C25-31 81 320 380 2000
PVH81BIC-RSF-10S-11-C25-31 81 320 380 2000

Notes on pressure & speed

  • Rated (continuous) pressure: 320–350 bar depending on control class; LS/compensator versions allow the full 350 bar continuously.
  • Peak pressure: 380–420 bar, short-duration only (≤10 % of duty cycle). Never use peak as a design setting.
  • Max speed is the mechanical limit at rated pressure; at 350 bar continuous the recommended working speed is 1800–2000 rpm to control case drain and oil temperature.
  • Minimum speed for stable LS control: approx. 300 rpm (below that, LS response becomes sluggish).
  • Case drain pressure must stay ≤ 2 bar (0.2 MPa) at all times; exceed it and the shaft seal and compensator behaviour are affected.
  • Speed × displacement gives theoretical flow: 81 cm³/rev → approx. 178 L/min at 2200 rpm, 146 L/min at 1800 rpm.