YUKEN Vane Pump Technical Document
Cover mainstream Yuken fixed PV2R series + variable SVPF / RV20 vane pumps (industry standard English datasheet version)
1. General Description
YUKEN vane pumps are balanced vane type hydraulic pumps, split into fixed displacement (PV2R single / double) and variable displacement (SVPF, RV20).
Balanced structure eliminates radial load on the shaft, featuring low noise, stable output, compact size and easy cartridge replacement. Widely used in injection moulding machines, machine tools, press machines, automation power packs and general industrial hydraulic systems.
2. Main Features
-
Balanced vane design: Low shaft radial force, long service life
-
Low noise structure, optimized flow pulsation
-
Cartridge kit construction: Quick on-site maintenance without whole pump replacement
-
Double pump version available: Two independent flows from one pump body for dual-circuit systems
-
Variable types with built-in pressure compensator: Energy saving, reduce heat generation at standby pressure
-
Wide fluid compatibility: Anti-wear oil, water-glycol, phosphate ester (special seal version)
3. Model Nomenclature
PV2R Fixed Single Vane Pump Example
PV2R1-19-F-RAA-41
-
PV2R1: Frame size 1
-
19: Nominal displacement (cm³/rev)
-
F: Flange mounting; L = Foot mounting
-
R: Rotation (clockwise viewed from shaft end, L = counter-clockwise)
-
AA: Port orientation
-
41: Design number
SVPF Variable Vane Pump Example
SVPF-40-70-20
-
SVPF: Variable displacement vane pump
-
40: Max delivery @1800 rpm (L/min)
-
70: Max pressure setting (kgf/cm²)
-
20: Design number
4. Main Specifications
PV2R Fixed Single Vane Pump
| Model | Displacement cm³/rev | Rated Pressure MPa | Max Pressure MPa | Speed Range r/min |
|---|---|---|---|---|
| PV2R1 | 5.8~25.3 | 16 | 21 | 600–1800 |
| PV2R2 | 26~47 | 16 | 21 | 600–1800 |
| PV2R3 | 52~76 | 16 | 21 | 600–1800 |
| PV2R4 | 81~237 | 14 | 17.2 | 600–1800 |
SVPF Variable Vane Pump
| Model | Max Flow L/min@1800rpm | Pressure Adjust Range kgf/cm² | Speed Range r/min |
|---|---|---|---|
| SVPF-12 | 12 | 10~70 | 800–1800 |
| SVPF-20 | 20 | 10~70 | 800–1800 |
| SVPF-30 | 30 | 10~70 | 800–1800 |
| SVPF-40 | 40 | 10~70 | 800–1800 |
5. Hydraulic Fluid Requirements
-
Recommended oil: Anti-wear hydraulic oil ISO VG32 / VG46
-
Viscosity range: 20 ~ 400 mm²/s
-
Operating oil temperature: 0 ~ 60°C (water-glycol limited to 50°C)
-
Cleanliness: NAS 10 or better; 10 μm return line filter recommended
-
Special fluid: Phosphate ester / water-glycol need special seal specification at ordering
6. Installation & Piping
-
Coupling: Flexible coupling required; TIR misalignment ≤0.1 mm, angular misalignment ≤0.2°
-
Suction line: Suction pressure −16.7 ~ +50 kPa; suction pipe inner diameter not smaller than pump suction port
-
Drain line (variable pump): Case backpressure ≤0.03 MPa, drain pipe below oil level, no throttle valve on drain line
-
Pre-filling: Fill pump cavity with clean hydraulic oil before initial startup
-
Bleeding: Remove air from suction and discharge circuit to prevent noise and cavitation
7. Adjustment (Variable SVPF / RV20)
-
Pressure adjusting screw: Clockwise → pressure rise; lock nut after setting
-
Flow adjusting screw: Clockwise → reduce maximum flow; counter-clockwise → increase flow
-
Factory preset: Max flow, minimum pressure setting
8. Control & Version Summary
-
PV2R: Fixed displacement, single / double pump
-
SVPF: Small variable vane pump for power pack, built-in pressure compensator
-
RV20: Medium-duty variable vane pump for machine tools, power saving cut-off function
-
PV2R double pump: Combined two cartridge sets, separate pressure adjustment for each circuit
9. Caution Notes
-
Do not run the pump without load and oil for more than several seconds
-
For phosphate ester fluid, confirm seal code F on model code
-
If noise increases sharply, check suction filter blockage, air ingress or fluid viscosity
-
Cartridge replacement must use genuine Yuken kit, follow disassembly sequence